基于精益6滓的航空高强钢零件大尺寸面轮廓度 数控加工参数优化

针对某航空高强钢零件大尺寸面轮廓度数控加工合格率较低问题,利用精益6σ方法,依据DMAIC的研究路径,充分运用箱线图、等方差检验、单因子方差分析等方法和工具,分析了“人、机、料、法、环、测”6大方面的操作者、加工刀具、装夹方式、主轴转速、切削量、进给速度、切削方式7个因素,确定刀具尺寸、切削量、进给速度为关键影响因素;通过建立面轮廓度与7个影响因素之间的GLM模型,得出影响流程输出的3个关键影响因素的最佳组合,并在此基础上对工艺参数进行优化。结果表明:该零件的数控加工工艺流程改进后,减少了加工过程中的人工调试检查环节,缩短了加工调试验证时间,大尺寸面轮廓度数控加工合格率从80%提高到96%以上,取得了较好的经济效益。     

基于航空煤油重整的SOFC-GT混合动力系统性能

建立了基于航空煤油重整固体氧化物燃料电池-涡轮发动机（SOFC-GT）混合动力系统仿真模型,比较了两种回热方式的重整装置以及不同涡轮布置位置时的系统性能变化,优选出最佳的混合动力系统架构。进一步分析了压气机压比、燃料利用率、燃油流量以及空气流量等运行参数对SOFC-GT混合动力系统性能的影响。研究结果表明：设计点工况下,最佳混合动力系统的发电效率能达到45%,体现出良好的系统性能;当燃料利用率为082时混合动力系统的效率和功率最高;随着燃油流量(0051 1~0058 4 mol/s)的增加,混合动力系统的效率和功率均增加;而随着压气机压比(25~33)或者空气流量(37~44 mol/s)的增加,混合动力系统的效率和功率都减小。     

纳米铝粉的活性评价方法研究进展

综述了纳米铝粉活性的2类评价方法:单质铝含量法和热分析参数法.单质铝含量的测定方法主要有气体容量法、氧化还原滴定法、热重分析法和透射电镜分析法,其中氧化还原滴定法又可分为重铬酸钾滴定法、水溶剂高锰酸钾滴定法、非水溶剂高锰酸钾滴定法及硫酸高铈法.基于热分析参数的活性评价方法主要采用:氧化起始温度、最大氧化速率、一定温度范...     

Comparison of peak characteristics of F2 ionospheric layer over Tehran region at a low solar activity period with IRI-2001 and IRI-2007 models predictions

In the present work values of peak electron density (NmF2) and height of F2 ionospheric layer (hmF2) over Tehran region at a low solar activity period are compared with the predictions of the International Reference Ionosphere models (IRI-2001 and IRI-2007). Data measured by a digital ionosonde at the ionospheric station of the Institute of Geophysics, University of Tehran from July 2006 to June 2007 are used to perform the calculations. Formulations proposed by  and  are utilized to calculate the hmF2. The International Union of Radio Science (URSI) and International Radio Consultative Committee (CCIR) options are employed to run the IRI-2001 and IRI-2007 models. Results show that both IRI-2007 and IRI-2001 can successfully predict the NmF2 and hmF2 over Tehran region. In addition, the study shows that predictions of IRI-2007 model with CCIR coefficient has closer values to the observations. Furthermore, it is found that the monthly average of the percentage deviation between the IRI models predictions and the values of hmF2 and NmF2 parameters are less than 10% and 21%, respectively.     

复杂薄壁、薄板类零件高速加工技术初探

从加工方法,加工参数,工装夹具等方面对薄壁、薄板类零件的加工进行深入探讨,有效地解决了薄壁、薄板类零件的加工,为今后进行此类零件的加工进行了有益的技术储备。     

Mechanism parameters optimization of bionic frog jumping robot based on velocity directional manipulability measure

以速度方向可操作度作为跳跃性能的评价指标,从机构设计角度寻求改善仿蛙跳跃机器人跳跃性能的方法.在仿蛙跳跃机器人机构模型的基础上,建立了起跳阶段的运动学方程,得到机器人从关节空间到质心运动空间的速度映射关系,结合速度方向可操作度,利用优化算法对仿蛙跳跃机器人的机构参数进行优化,使机器人的跳跃性能达到最佳.优化结果表明,运用速度方向可操作度理论,对跳跃机器人机构参数进行优化研究是有效可行的.     

Using the MIR bands in vegetation indices for the estimation of grassland biophysical parameters from satellite remote sensing in the Alps region of Trentino (Italy)

Development of new methods for estimating biophysical parameters can be considered one of the most important targets for the improvement of grassland parameters estimation at full canopy cover. In fact, accurate assessment methods of biophysical characteristics of vegetation are needed in order to avoid the uncertainties of carbon terrestrial sinks.

Remote sensing is a valid tool for scaling up ecosystem measurements towards landscape levels serving a wide range of applications, many of them being related to carbon-cycle models. The aim of this study was to test the suitability of satellite platform sensors in estimating grassland biophysical parameters such as LAI, biomass, phytomass, and Green herbage ratio (GR). Also, we wanted to compare some of the most common NIR and red/green-based vegetation indices with ones that also make use of the MIR band, in relation to their ability to predict grassland biophysical parameters.

Ground-truth measurements were taken on July 2003 and 2004 on the Monte Bondone plateau (Italian Alps, Trento district) in grasslands varying in land use and management intensities. From satellite platforms, an IRS-1C-LISS III image (18/07/2003; 25 m resolution in the visible-NIR and 70 m resolution in the MIR) and a SPOT 5 image (27/07/2004, 10 m resolution in the visible-NIR and MIR) were used.

LAI, biomass, and phytomass measurements showed logarithmic relationships with the investigated NIR and red/green-based indices. GreenNDVI showed the highest R² values (0.59, IRS 2003; 0.60, SPOT 2004). Index saturation occurred above approximately 100–150 g m⁻² of biomass (LAI 1.5–2). On the other hand, GR relationships were shown to be linear. MIR-based indices performed better than NIR and red/green-based ones in estimating biophysical variables, with no saturation effect. Biomass showed a linear regression with Canopy Index (MIR/green ratio) and with the Normalised Canopy Index (NCI) calculated as a normalised difference between MIR and green bands (IRS: R² = 0.91 and 0.90, respectively. SPOT: R² = 0.63 and 0.64). Similar correlations could also be found for LAI and phytomass, and GR predictability was shown to be higher than NDVI and GreenNDVI. According to these results obtained in the investigated areas, phytomass, biomass, LAI, and GR are linearly correlated with the investigated MIR band indices and as a result, these parameters could be estimated from the adopted satellite platforms with limited saturation problems.     

GRACE gravity field modeling with an investigation on correlation between nuisance parameters and gravity field coefficients

The GRACE (Gravity Recovery And Climate Experiment) monthly gravity models have been independently produced and published by several research institutions, such as Center for Space Research (CSR), GeoForschungsZentrum (GFZ), Jet Propulsion Laboratory (JPL), Centre National d’Etudes Spatiales (CNES) and Delft Institute of Earth Observation and Space Systems (DEOS). According to their processing standards, above institutions use the traditional variational approach except that the DEOS exploits the acceleration approach. The background force models employed are rather similar. The produced gravity field models generally agree with one another in the spatial pattern. However, there are some discrepancies in the gravity signal amplitude between solutions produced by different institutions. In particular, 10%–30% signal amplitude differences in some river basins can be observed. In this paper, we implemented a variant of the traditional variational approach and computed two sets of monthly gravity field solutions using the data from January 2005 to December 2006. The input data are K-band range-rates (KBRR) and kinematic orbits of GRACE satellites. The main difference in the production of our two types of models is how to deal with nuisance parameters. This type of parameters is necessary to absorb low-frequency errors in the data, which are mainly the aliasing and instrument errors. One way is to remove the nuisance parameters before estimating the geopotential coefficients, called NPARB approach in the paper. The other way is to estimate the nuisance parameters and geopotential coefficients simultaneously, called NPESS approach. These two types of solutions mainly differ in geopotential coefficients from degree 2 to 5. This can be explained by the fact that the nuisance parameters and the gravity field coefficients are highly correlated, particularly at low degrees. We compare these solutions with the official and published ones by means of spectral analysis. It is found that our solutions are, in general, consistent with others in the spatial pattern. The water storage variations of the Amazon, Chari and Ganges river basins have also been computed. The variations computed with the NPARB approach are closer to those produced by JPL and DEOS solutions, while the variations produced with the NPESS approach are in good agreement with those produced by the CSR and GFZ solutions. A simulation study is implemented with considering realistic noise and low-frequency error. The two approaches are used to recover the true model. The NPESS solution appears closer to the true one. Therefore we are inclined to estimate the nuisance parameters simultaneously with the geopential coefficients.     

2级脉冲爆震发动机中超声速射流对撞诱导激波聚焦试验研究

为研究2-St age PDE中连续超声速射流及结构参数对撞诱导激波聚焦的影响规律,在冷态条件下开展了2-St age PDE中连续超声速射流对撞诱导激波聚焦的试验。分析了喷口宽度、导流环深度、凹面腔开口端与喷管间距、尾喷管角度、射流入射压力等参数对凹面腔底部峰值压力的影响。结果表明:喷口宽度、导流环深度、凹面腔开口端与喷口间距、射流入射压力越大,凹面腔底部峰值压力越大,激波聚焦效果越好;尾喷管角度越大,凹面腔底部峰值压力越小,激波聚焦效果越差;喷口宽度、导流环深度、射流入射压力对激波聚焦的影响较大。     

自由返回轨道的P平面参数快速设计方法

针对自由返回轨道求解过程中地心轨道类型变化造成的B平面参数方法计算失败问题,提出一种基于P平面参数的自由返回轨道快速设计方法。首先,基于轨道半通径参数的普适性,给出了不同轨道类型的P平面参数定义,建立了以P平面参数为求解目标量的自由返回轨道求解模型。其次,给出了基于P平面参数的自由返回轨道快速设计方法,在构建的瞬时地月惯性系下,以平面双二体自由返回轨道作为初值,实现了高精度力模型下的自由返回轨道快速求解。对8种构型自由返回轨道的设计结果表明,P平面参数具有类似于B平面参数的大收敛域,且有效解决了轨道类型变化对计算的影响,可直接应用于中国后续月球探测任务轨道设计。